top of page
International Journal Publications
2005 - 2009
79 / Arun Prakash N, Gnanamoorthy, R and Kamaraj (2009) ‘Friction and wear behaviour of surface nanocrystallized Al alloy under dry lubricated conditions’, Mat. Sci. Eng B 168 176-181 (JIF 1.577)
78 / Ramkumar A, K Kannan, Gnanamoorthy R (2010) ‘Experimental and theroritical investigation of a polymer subjected to cyclic loading’ Int. J. Eng. Sci., 48 (2) 101-110 (JIF 1.366)
77 / Kirupasankar, S., Gnanamoorthy, R., Velmurugan, R. Effect of apparent area, load, and filler content on sliding friction characteristics of polymer nanocomposites (2010) Proc of the Inst of Mech Engineers, Part J: J of Engg Tribology, 224 (2), pp. 133-138.
76 / M Mubarak Ali, Ganesh Sundara Raman S, Pathak SD, Gnanamoorthy R, (2010) ‘Influence of plasma nitriding on fretting wear of Ti-6Al-4V’, Tribology Int, 43 (1-2) 152-160.
75 / A Sahaya Grinspan and R Gnanamoorthy (2009) ‘Development of a Novel Oil Cavitation Jet Peening System and Cavitation Jet Erosion in aluminum alloy, AA 6063 T6’, Trans ASME. J Fluid Engg, 131 (6) Art No. 061301.
74 / P Navaneethakrishnan, Ganesh Sundara Raman S, R Gnanamoorthy, Ravi, P (2009) ‘Relative performance of hydrogenated, argon incorporated and nitrogen incorporated diamond like carbon -coated Ti-6Al-4V samples under fretting wear conditions’, Thin Solid Films, 517 (15) 4365-4371.
73 / Ganesh Sundara Raman S, P Navaneethakrishnan, R Gnanamoorthy (2009) ‘Influence of counter body material on fretting wear behaviour of uncoated and diamond-like carbon-coated Ti-6Al-4V’, Proc. IMechE Pt J: J. Engg Tribology, 223 (2)227-232.
72 / Navaneethakrishnan P, Ganesh Sundara Raman S, Pathak SD, Gnanamoorthy R, Ravi N (2009) ‘Fretting wear studies on diamond-like carbon coated Ti-6Al-4V’, Surface and Coatings Tech, 203(9): 1205-1212.
71 / Senthilvelan S, R Gnanamoorthy (2009) ‘Efficiency of injection molded polymer gear’ Proc. IMechE Pt J: J. Engg Tribology 223 (6), pp. 925-928.
70 / Ali, M.M., Raman, S.G.S., Pathak, S.D., Gnanamoorthy, R. Fretting wear behaviour of plasma nitrided Ti-6Al-4V fretted against unnitrided Ti-6Al-4V and alumina counterbodies (2009) Trans of the Indian Institute of Metals, 62 (1), pp. 59-64.
69 / Kodeeswaran M, Gnanamoorthy R (2008) ‘Effect of strain rate on nanocrystalline surface formation in controlled ball impact process in AISI 304 SS’, Materials Letters, 62 (30), 4516-4518.
68 / Ramkumar A, Gnanamoorthy R (2008) ‘Axial fatigue behaviour of polyamide-6 and polyamide-6 nanocomposites at room temperature’ Composites Sci and Tech, 68 (15-16), 3401-3405.
67 / N Govindarajan, R Gnanamoorthy (2008) ‘Computation of sliding friction and ratcheting of sintered and hardened steel under rolling contact fatigue’, ASME J of Tribology, 130 (4), Art. no. 041602 .
66 / S Dhanasekaran, R Gnanamoorthy (2008) ‘Gear tooth wear in sintered steel gears under dry running conditions’ Wear, 265, 81/87 [JIF=1.404].
65 / S Senthilvelan, R Gnanamoorthy (2008) ‘Influence of reinforcement on composite gear metrology’ Mechanism and Machine Theory, 43 (9), 1198-1209 [JIF=0.75].
64 / Shanmugavel M, Nandagopal M, Sandya R, Bhanusankara Rao K, Gnanamoorthy R, (2008) ‘Evaluation of activation energy for dynamic strain aging process in 316l(n)/316(n) SS weld joints’ Trans of Indian Inst of Metals. 61 (4) 301-306.
63 / S Dhanasekaran and R Gnanamoorthy (2007) ‘Heat generation in Fe-C-Cu-MoS2 sintered spur gears under unlubricated conditions’, Proc. IMechE Pt J: J. Engg Tribology, 221(J6), 645-652.
62 / G Srinath, R Gnanamoorthy (2007) ‘Effect of organoclay addition on the two-body abrasive wear characteristics of polyamide nanocomposites’, J Mat Sci, 42, 8326-8333 [JIF=0.91].
61 / A Sahaya Grinspan, R Gnanamoorthy (2007) ‘Effect of nozzle traveling velocity on oil cavitation jet peening of aluminum AA 6063 -T6’, ASME J Engg Mat & Tech 129 (4), 609-613.
60 / A Sahaya Grinspan, R Gnanamoorthy (2007) ‘Fatigue behavior of oil jet peened Al alloys AA6063 T6’, JSME J Solid Mech & Mat Engg, 1, 875-885.
59 / Aravind Vadiraj, M Kamaraj and R Gnanamoorthy (2007) ‘Fretting wear studies on PVD TiN coated ion implanted, thermally oxidised biomedical titanium alloys’, Surf Engg, 23, 209 [JIF=0.44].
58 / S Dhanasekaran and R Gnanamoorthy (2007) ‘Microstructure, strength and tribo behavior of Fe-C-Cu-Ni sintered steels containing MoS2’, J Mat Sci, 42 4659-4666.
57 / N Govindarajan and R Gnanamoorthy (2007) ‘Rolling / sliding contact fatigue life prediction of sintered and hardened steels’, Wear, 262, 70-78 [JIF=1.404].
56 / A Sahaya Grinspan and R Gnanamoorthy (2007) ‘Effect of oil jet peening duration on surface modification and fatigue behaviour of medium carbon steel AISI 1040’, Mat Sci & Eng A, 456, 210-217. [JIF=1.35]
55 / A Sahaya Grinspan, R Gnanamoorthy (2007) ‘Surface modification and fatigue behaviour of oil jet peened medium carbon steel, AISI 1040’, ASME J Manf Sci 129 (3), 601-6624.
54 / R Ramesh, R Gnanamoorthy (2007) ‘An investigation on the fretting wear behavior of MoS2 bonded coating on AISI 1040 Proc. IMechE Pt J: J. 221, 41-47
53 / S Dhanasekaran and R Gnanamoorthy (2007) ‘Abrasive wear behavior of sintered steels prepared with MoS2 addition’ Wear, 262, 617-623. [JIF=1.404]
52 / Dipa Roy, R Gnanamoorthy (2007) ‘Friction and wear behaviour of vinyl ester resin matrix composites filled with fly ash particles’ J Reinf. Plastics & Comp, 26, 5-13.
51 / G Srinath, R Gnanamoorthy (2007) ‘Sliding wear performance of polyamide 6 – clay nanocomposites in water’ Comp Sci & Tech. 67, 399-405 [JIF=2.184].
50 / N Govindarajan, R Gnanamoorthy (2007) ‘Study of damage mechanisms and failure analysis of sintered hardened steels under rolling/sliding contact conditions’, Mat Sci & Engg A A445, 259-268. [JIF=1.35]
49 / Aravind Vadiraj, M Kamaraj, R Gnanamoorthy (2007) ‘Fretting wear studies on uncoated, plasma nitrided, and laser nitrided biomedical titanium alloys’, Mat Sci & Engg A 445, 446-453. [JIF=1.35]
48 / R Ramesh and R Gnanamoorthy (2007) ‘Artificial neural network prediction of fretting wear behavior of structural steel against bearing steel’ ASM J Mat Engg & Perf 16 (6), 703-709 [JIF=0.816].
47 / R Ramesh R Gnanamoorthy (2007) ‘Effect of hardness on fretting wear behaviour of structural steel, En24 against bearing steel, En31’ Mat & Design, 28, 1447
46 / S Dhanasekaran and R Gnanamoorthy (2007) ‘Dry sliding friction and wear characteristics of Fe-C-Cu alloy containing molybdenum di sulphide’, Mat & Design 28, 1135-1141. [JIF=0.785]
45 / S Senthilvelan and R Gnanamoorthy (2007) ‘Effect of rotational speed on the performance of unreinforced and glass fibre reinforced nylon 6 spur’, Mat & Design, 28, 7652 [JIF=0.785].
44 / A. Sahaya Grinspan and R Gnanamoorthy (2007) ‘Surface modification of steel using liquid jet peening – fatigue performance’, Mat Sci Forum, 539, 1140-1145.
43 / G Srinath and R Gnanamoorthy (2006)‘Two-body abrasive wear characteristics of nylon clay nanocomposites - effect of grit size, load, and sliding velocity’ Mat Sci & Engg A. 435-436, 181-186. [JIF=1.35]
42 / S Senthilvelan and R Gnanamoorthy (2006) ‘Fibre reinforcement in injection molded nylon 66 spur gears Appl Comp Mat, 13, 237-248. [JIF=0.84]
41 / A Sahaya Grinspan and R Gnanamoorthy (2006) ‘Surface modification induced in 6063-t6 & AA6061-t4 by oil jet peening: I. Residual stress & hardness, Appl Surf Sci 253, 989. [JIF=1.263]
40 / A Sahaya Grinspan and R Gnanamoorthy (2006) ‘Surface modification induced in 6063-t6 & 6061-t4 by oiljet peening: II. Surface morphology, erosion & mass Loss’ Appl Surf Sci, 253, 998. [JIF=1.263]
39 / A Sahaya Grinspan and R Gnanamoorthy (2006) ‘A novel surface modification technique for introduction compressive residual stress and studies on 6063’ Surf & Coat Tech, 201, 1768.
38 / S Senthilvelan and R Gnanamoorthy (2006) ‘Selective carbon fiber reinforced nylon 66 spur gears: development and performance’ Appl Comp Mat, 13, 43-56. [JIF=0.84]
37 / S Senthilvelan and R Gnanamoorthy (2006) ‘Effect of gear tooth fillet radius on the performance of injection molded nylon 66 gears’, Mat & Design, 27, 632-639.
36 / R Ramesh and R Gnanamoorthy (2006) ‘Effect of post oxidation on the fretting wear performance of liquid nitrided En24 steels’, Surf & Coat Tech, 200, 3926-3932.
35 / P Jawahar, R Gnanamoorthy and M. Balasubramanian (2006) ‘Tribological behaviour of clay – thermoset polyester nanocomposites’ Wear, 261, 835-840.
34 / S Senthilvelan, R Gnanamoorthy (2006) ‘Damping characteristics of unreinforced, glass and carbon fiber reinforced nylon 66 spur gears’, Polymer Testing, 25, 56-62.
33 / R Ramesh and R Gnanamoorthy (2006) ‘Fretting wear behavior of as received, hardened - tempered and liquid nitrided structural steel, En24, against bearing steel, En31’, J Mat Proc Tech, 171, 61-67. [JIF=0.6].
32 / R Ramesh and R Gnanamoorthy (2006) ‘Development of a fretting wear test rig and preliminary studies for understanding the fretting wear properties of steels’, Mat & Design, 27, 141. [JIF=0.79]
31 / S Senthilvelan and R Gnanamoorthy (2005) ‘Surface failure analysis of unreinforced, glass and carbon fibre reinforced Nylon 6/6 gears’ Int J of Plastics Tech, 9, 444.
30 / S Senthilvelan and R Gnanamoorthy (2005) ‘Reinforced polymer gear fatigue and failure analysis’ Tran Ind Inst of Metals, 58, 249-253.
29 / G Srinath and R Gnanamoorthy, (2005) ‘Effect of nanoclay reinforcement on tensile and tribo behavior of nylon 6’, J Mat Sci, 40, 2897-2901. [JIF=0.91]
28 / G Srinath and R Gnanamoorthy, (2005) ‘Effect of short fibre reinforcement on the friction and wear behaviour of nylon 66’, Appl Comp Mat, 12, 369-383. [JIF=0.84]
27 / P Jawahar, R Gnanamoorthy, and M Balasubramanian (2005) ‘Flexural and tribological properties of polyester clay nanocomposities, J Mat Sci Let, 40, 4391.
bottom of page